Polymer Production Operator

Job DescriptionJob Description

POLYMER PRODUCTION OPERATOR SUMMARY:

The Production Operator will safely control various equipment to produce products on the Production Line.

POLYMER PRODUCTION OPERATOR ESSENTIAL DUTIES AND RESPONSIBILITIES:

• Clean mold jackets and mold core, clearing away any excess flashing, wax, and foreign debris.
• Scrape flashing from product.
• Visually inspect for quality, i.e. holes, cracks, uneven rails, short rails, etc. tell Team Leader if questionable.
• Set product in curing rack if quality is acceptable or scrap it if the quality is not acceptable; insert grates where applicable.
• Remove from curing rack when next piece is ready, (leaving larger channels in the rack for two rounds) and move from curing rack to pallet or to patch area if needed.
• Apply a thin coat of hot wax to top surface of mold only (consistency of wax must be liquid).
• Clean knockouts.
• Re-assemble jackets and end caps of mold so that they close properly. Insert K-rails or SK100 rails if needed. Make sure rails seat correctly in mold.
• Check to make sure inner bars are closed, if not, pull inner bars firmly to right of mold using wrench.
• Double-check that mold is closed properly. (There should be no gaps between the mold jackets and the end caps.)
• Maintains a clean, safe, and orderly work area.
• Comply with Company policies and procedures

Duties and responsibilities will change depending on what product is being manufactured.

SPORT PRODUCTS: (2000 & 3000 products)

Only used in the Casa Grande location

• Using the small lift crane, pull channel straight upward, taking care not to chip end.
• Eject core of mold with arrow pointing to the right.
• Clean flashing from ends and center slot, check for defects on the critical surfaces.
• Wax core every other round, place it back in the mold jacket.
• Clean mold: end caps, flat surface & where jackets contact the base of the mold.
• Place channel on appropriate skid or notify Leadman of defects or problems.

POLYMER PRODUCTION OPERATOR COMPENTENCIES:

Teamwork

Attention to Detail

Knowledge

Technical Capacity

POLYMER PRODUCTION OPERATOR EDUCATION and/or EXPERIENCE:

High school diploma or general education degree (GED)

POLYMER PRODUCTION OPERATOR PHYSICAL DEMANDS:

The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

• Prolonged periods working on feet, using tools, and performing repetitive actions that entail frequent bending and stooping.
• Required regularly to use hands to handle or feel and reach with hands and arms.

• Must be able to squat, stand, stoop bend down, for long periods of time.
• Required to occasionally climb or balance; stoop, kneel, and crouch; and talk or hear.
• Must be able to lift, push, and pull a minimum of 75lbs and maximum of 100lbs.
• Visual acuity to read instructions, operate machines, and inspect parts produced

POLYMER PRODUCTION OPERATOR ADDITIONAL ELIGIBILITY QUALIFICATIONS:

To perform this job successfully, an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill, and/or ability required.

• Ability to apply common sense understanding to carry out general instructions.
• Ability to deal with standardized situations with occasional variables.
• Ability to follow directions and work well in a team.
• Thorough understanding of or the ability to quickly learn production equipment.
• Understanding of and the ability to abide by applicable OSHA and environmental regulations.

This position is designated as “safety sensitive” pursuant to A.R.S. Sections 23-493(9) and 23 493.06(7).)

POLYMER PRODUCTION OPERATOR OTHER DUTIES:

The above is intended to describe the general content of and requirements for the performance of this job. It is not to be construed as an exhaustive statement of duties, responsibilities or physical requirements. Nothing in this job description restricts management’s right to assign or reassign duties and responsibilities to this job at any time. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.

#ZR

Company DescriptionWhy work for ACO?

Join a global family owned company with office/ production in 45+ countries that has been in business for 75 years. ACO products are designed and manufactured with the belief that the company positively impacts the use of one of earth’s greatest resources, water. ACO is rooted with the team player spirit, encouraging self-development and growth, and promotes a safe and healthy work environment for all of its employees.Company DescriptionWhy work for ACO?\r\n\r\nJoin a global family owned company with office/ production in 45+ countries that has been in business for 75 years. ACO products are designed and manufactured with the belief that the company positively impacts the use of one of earth’s greatest resources, water. ACO is rooted with the team player spirit, encouraging self-development and growth, and promotes a safe and healthy work environment for all of its employees.